Rolling bearings are ball bearings, roller (tapered) bearings and needle bearings. They often work at high speeds and under heavy loads. After long-term use, wear, ablation, fracture, fatigue spalling and spots will occur on rolling bodies and raceways.

　　滾動軸承一般不拆供檢查。在檢驗過程中進行清洗，通過外部檢驗、空轉檢驗和內部間隙檢驗來判斷其質量。

　　Rolling bearings are generally not disassembled for inspection. In the process of inspection, cleaning is carried out, and its quality is judged by external inspection, idling inspection and internal clearance inspection.

　　1. 外檢發現有下列情況之一的，應當更換或者修改。

　　1. If one of the following circumstances is found in the external inspection, it shall be replaced or modified.

　　(1)鋼球、滾子及內外滾道因燒蝕而改變原有光澤。

　　(1) The original luster of steel balls, rollers and inner and outer raceways is changed by ablation.

　　(2)軸承內外滾道產生撞擊痕跡、擦傷、擦傷和異常磨損。

　　(2) The internal and external raceways of bearings produce impact marks, scratches, abrasions and abnormal wear.

　　(3)軸承內外滾道、鋼球和滾子裂紋、金屬分層、水垢剝落及大量黑點。

　　(3) Cracks in inner and outer raceways, steel balls and rollers, metal delamination, scale peeling and a large number of black spots of bearings.

　　(4)在隔離環中，密封圈有穿透性裂紋，缺少鉚釘或松動。

　　(4) In the isolation ring, there are penetrating cracks in the sealing ring, lack of rivets or loosening.

　　(5)鋼球隔離環槽磨損過大，鋼球會自行脫落。

　　(5) The steel ball isolation ring groove wears too much, and the steel ball will fall off by itself.

　　6. 軸承隔震圈端面磨損深度大于0.30mmo

　　6. End face wear depth of bearing isolation ring is greater than 0.30 MMO

　　圓錐滾子磨損時，工作面的小端面凸出在軸承外的閥座環端面上。

　　When tapered roller wears out, the small end face of the working face protrudes on the end face of the seat ring outside the bearing.

　　我們圓錐滾子軸承內圈內圈內端面切口大，金屬剝落。

　　Our tapered roller bearing inner ring inner end face cut large, metal peeling.

　　如果只有輕微腐蝕性黑點在軸承和輕微缺陷隔離環圈而不影響旋轉,不超過4破洞的周長的法蘭表面小的圓錐滾子軸承的內圈環,和兩個相鄰孔有一定的距離,它仍然可以被使用。

　　If only slightly corrosive black spots are present in the bearing and slightly defective isolation ring without affecting rotation, the inner ring of a small tapered roller bearing with a flange surface no more than 4 holes and a distance from two adjacent holes can still be used.

　　2. 空轉試驗:空轉軸承，檢查軸承轉動是否輕巧靈活，無噪聲、滯止、堵塞。軸承旋轉的不均勻性可以通過手的感覺來判斷。

　　2. idle test: idle bearing, check whether the rotation of the bearing is light and flexible, no noise, stagnation, blockage. The non-uniformity of the bearing rotation can be judged by the feeling of the hand.

　　3.通過檢查滾珠軸承的徑向間隙和軸向間隙，檢查滾珠軸承的磨損情況，確定是否在規定的值范圍內。

　　3. By checking the radial and axial clearances of ball bearings, checking the wear of ball bearings, determine whether in the specified value range.